Are you looking to add some new life to your home’s exterior?
One great way to do that is by installing turf on your PVC sheathing or plywood. Here’s step-by-step guidance: keep reading to learn more!
Step 1:
Installing artificial turf is a great way to add a lovely aesthetic to your outdoor space. After the PVC sheathing and plywood subfloors have been installed, the next step is unrolling the artificial turf, allowing it to flatten. Ensure the artificial turf remains flat by strategically placing the weights along the edges. Taking this step will keep the artificial turf in its ideal position so that you can enjoy your new outdoor space.
Step 2
When laying artificial grass in Loveland, CO, on PVC sheathing and plywood, it’s critical to thoroughly clean them before application. To ensure proper adhesion, wash the sheathing with a grease-fighting detergent to remove the oils, grease, and dirt that could prevent the turf from sticking. After washing, allow the sheathing to dry completely so there is no remaining moisture. High saturation levels can damage both the sheathing and any adhesive you may use for installation. Using minimal water on plywood will help ensure proper adhesion and stable structure. Be sure it’s clean and dry before getting started!
Step 3
After all the preparations are complete, and the materials gathered, it’s time to begin the installation of the turf. Take out a piece of 80-grit sandpaper and insert it into a sanding block. Gently sand the PVC surface to remove its smooth finish and give it some texture. The same applies to plywood; lightly rub it to roughen the surface. Artificial turf adhesive sticks better when bonded with a roughed-up than a smooth surface, guaranteeing higher quality installs built to last longer and offer added protection against future damages. In conclusion, this is an essential step for mounting turf that shouldn’t be skipped!
Step 4
Laying turf on top of plywood or PVC sheathing isn’t as difficult as it may seem. Start by placing the turf over either material, making sure to line it up evenly along the edges. If your first piece of turf is not wide enough to cover the entire length, you’ll need to get a second section and press it against the first piece snugly. This ensures there will be no gaps between them when the job is complete.
Step 5
After securing the sheathing or plywood to the ground, it’s time to cut your artificial turf for the application. Carefully measure and mark about 2-3 inches larger than the size of your sheathing or plywood in all directions, then use a utility knife or carpet scissors to cut the artificial turf along these measurements. By creating this margin space, you can secure the edges of the turf once it’s mounted in place.
Step 6
When laying out the artificial turf, it’s essential to be sure that it is as smooth as possible: place a heavy weight on the center of the turf roll, or a helper can stand there to hold it in place while you smooth. Alternatively, the turfed area can be pulled back and folded in half or have a helper hold one side of the turf off the surface while making adjustments. This will allow you to easily move and shape sections of turf to achieve even coverage. Ultimately, this will create a professional-looking finish with minimal effort!
Step 7
Applying artificial turf adhesive to plywood or PVC sheathing is crucial when laying turf. Specialized products can provide a strong bond for the synthetic turf to both these surfaces. Spread the adhesive evenly over the surface with a trowel and work it into the grooves of the plywood. Using enough glue to secure the turf is essential, as this will ensure it stays in place while also reducing wear and tear. Follow all instructions carefully, paying attention to any health and safety considerations associated with working with this type of adhesive.
Step 8
Once the sheathing and plywood are in place, the next step is to pull the artificial turf over it and ensure it’s tightly secured. You’ll need to press each piece into the floor with your hands to ensure it’s firmly attached. Remember to do this for both halves of the structure, ensuring each side is covered securely. This will help ensure that your turf lasts for many years without any issues arising from loose or peeling areas. With this step complete, you can finish laying your turf and enjoy your freshly renovated space.
Step 9
To create a tight bond between the turf and substrate material, running a 100-lb. floor roller over the area is essential. This will also help smooth out any wrinkles that appear after laying down the turf pieces. If you have a helper, it’ll be easier to roll and compact the turf, as your helper can pull each piece tautly as you roll it. Make sure to roll over the turf firmly but not too hard or aggressively so that you inflict no damage on either the turf or subfloor.
Step 10
After you’ve laid out your turf and applied the adhesive, it’s essential to allow time for the adhesive to set. Ideally, you must wait four to six hours before continuing. Once the glue has had time to cure, you can use carpet scissors or a utility knife to trim off any excess turf to achieve a neat finish.
Artificial turf installed over PVC sheathing and plywood can create a fresh look that will last for years with minimal maintenance. With this guide to laying turf on PVC sheathing and plywood, homeowners can tackle this project confidently and keep safety first by wearing eye protection and gloves when handling the adhesive. So take your outdoor space from boring to brilliant by installing artificial turf today – and enjoy your beautiful new backyard!
